This section covers the alignment / Tuning of your 65CM White Dish
This guide will make it easier to get your Portable Satellite TV
Kit up and going quickly.
These are the items that you should have.
Unpack your items and setup your TV.
Install your remote control batteries.
Turn your TV on.
PLEASE DO NOT ACCESS THE "MENU" OF THE RECEIVER
AND CHANGE ANY SETTINGS OUR RECEIVERS ARE PRETUNED.
1. Connect your yellow / white / red cable to your tv.
2. If you do not have these connections on your tv , connect an antenna cable to the RF-OUT and plug it directly into the antenna connection on the back of your TV. DO NOT CONNECT BOTH.
3. Connect your satellite cable to the LNB IN on your satellite receiver.
4. Connect your power cable to your wall socket.
5. Turn the power switch on the back of the receiver "ON"
6. Turn on your TV on and select the correct AV channel your TV remote control, every TV is different please refer to your TV manual.
7. Press the power button on the front of the strong receiver.
8. The receiver should now be turned on, if there is a red light showing, please hit the power button one more time.
Select the the language you would like to use.
Press "group" or sat list on your remote and select
the corresponding satellite name for the service you are
trying to find.
Optus C1 = Optus Aurora Card "Gwn,Win,Abc,Sbs"
Optus D1 = Abc,Sbs, Abc2
Optus D2 = Overseas stations and local religious stations
Pas 8 = Selectv
You should now have a blank screen or "no or bad signal"
Now its all setup and ready to align, place your dish and tripod
where there is clear line of site to the North East direction.
Run your 20metre cable to the dish.
You will need to loosen the bolts on the side of the bracket,
then set the scale to the correct elevation.
This dish is a offset dish, therefore everything mark including "0"
is "10 degrees. Example: To set the dish to 30degrees, the point of
the bracket should be aligned with the second mark after "0".
Once this is done tigten the bolts.
Plug your satellite finder inline next to your satellite dish.
Plug the "REC" to receiver and "LNB" to dish.
Turn the dial till the needle sits on"5" and emits a high pitch squeel.
Use your compass to work out the general direction of where to
point the dish. Refer to the diagrams provided in the written
instructions or select your location and satellite below from the
provided dishpointer application.
The most popular satellite Optus C1 from Perth is 56* North/East
and 33* elevation.
Make sure you have clear line of site to the sky and your sat finder
in your hand and the needle reads "5".
Move your dish to the "West" , now move your satellite dish
to the North East direction, you should get a spike.
Once you have a spike on the needle between 7-10 tighten the
bolts on your dish. If the needle go's up to ten , wind it back to "7"
and keep moving your dish trying to find the "maximum" signal
that we can achieve.
You should now see the Optus Aurora or Selectv tuning station,
this station displays notifications, if you can see this screen
everything is working correctly and you can move on to STEP 10.
If you still have no picture, you have either locked on to the wrong
satellite or your signal is to weak. Please repeat "STEP7" until you
see the tuning station.
Remove the satellite finder from the dish and plug your long cable straight to the LNB/DISH.
If you are unable to receive the tuning station still after repating STEP7 please call our technical line.
ITECHWORLD TECHNICAL HELP LINE: 08 95272323
Slide your card in to the card slot in your receiver.
Call Optus aurora or Selectv to activate your card.
Optus Aurora: 1300 301 680
Selectv: 1300 735328
Your card can take upto 24 hours to activate , keep your dish
aligned and your receiver turned on with the card inserted.
Once your activation has been approved , you will start to receive
your tv stations. Press the up or down arrow on your remote
control to change between channels.
CONGRATULATIONS
YOU NOW HAVE A FULLY TUNED ITECHWORLD SATELLITE SYSTEM
